Treatment of Organics in Wastewater Using Electrogenerated Gaseous Oxidants.

This work focuses on the comparison of the performance of direct electrochemical oxidation with indirect electrolysis mediated by gaseous oxidants in the treatment of diluted wastewater. To do this, energy consumptions of the electrolysis using mixed metal oxide (MMO) electrodes are compared with those required for the production and use of chlorine dioxide in the degradation of methomyl contained in aqueous solutions. Results demonstrate the feasibility of the mediated oxidation process and that this process is competitive with direct oxidation. The oxidants are produced under optimized conditions using the same anodic material applied for the direct degradation of organics, thus avoiding efficiency losses associated with mass transfer limitations in the degradation of dilute organic solutions. Thus, using the ClO2 gaseous oxidant, a concentration of 0.1 mM of methomyl from a solution containing 500 mL is completely removed with an energy consumption as low as 50 Wh. The application of the same energy to a direct electrolytic process for treating the same wastewater can only reach less than half of this removal. These findings may have a very important application in the use of electrochemical technology to achieve the remediation of persistent pollutants in wastewater, where their low concentrations typically make direct processes very inefficient.

Associations of altered leukocyte DDR1 promoter methylation and childhood trauma with bipolar disorder and suicidal behavior in euthymic patients.

Altered DNA methylation (DNAm) patterns of discoidin domain receptor 1 (DDR1) have been found in the blood and brain of patients with schizophrenia (SCZ) and the brain of patients with bipolar disorder (BD). Childhood trauma (CT) is associated with changes in DNAm that in turn are related to suicidal behavior (SB) in patients with several psychiatric disorders. Here, using MassARRAY® technology, we studied 128 patients diagnosed with BD in remission and 141 healthy controls (HCs) to compare leukocyte DDR1 promoter DNAm patterns between patients and HCs and between patients with and without SB. Additionally, we investigated whether CT was associated with DDR1 DNAm and mediated SB. We found hypermethylation at DDR1 cg19215110 and cg23953820 sites and hypomethylation at cg14279856 and cg03270204 sites in patients with BD compared to HCs. Logistic regression models showed that hypermethylation of DDR1 cg23953820 but not cg19215110 and CT were risk factors for BD, while cg14279856 and cg03270204 hypomethylation were protective factors. In patients, CT was a risk factor for SB, but DDR1 DNAm, although associated with CT, did not mediate the association of CT with SB. This is the first study demonstrating altered leukocyte DDR1 promoter DNAm in euthymic patients with BD. We conclude that altered DDR1 DNAm may be related to immune and inflammatory mechanisms and could be a potential blood biomarker for the diagnosis and stratification of psychiatric patients.

Further Molecular Diagnosis Determines Lack of Evidence for Real Seed Transmission of Tomato Leaf Curl New Delhi Virus in Cucurbits.

Begomoviruses (family Geminiviridae) cause serious diseases in many crop families. Since 2013, the Spanish isolate of tomato leaf curl New Delhi virus (ToLCNDV) has been a limiting factor for cucurbits production in the Mediterranean basin, forcing farmers to adapt new management and control techniques. Although it is well-known that begomoviruses are naturally transmitted by the whitefly Bemisia tabaci, the capacity of these viruses to be vertically transmitted through seeds remains controversial. Clarifying the potential ToLCNDV seed transmission is essential to understand the epidemiology of this threating-for-cucurbits virus and to design appropriate control strategies. We assessed ToLCNDV distribution in the leaves, flowers and seeds of the infected plants of susceptible Cucumis melo accessions and toleration to the infected genotypes of Cucurbita moschata by conventional and quantitative PCR. We analyzed whether the viral particle was transmitted to offspring. We also evaluated ToLCNDV presence in commercial seeds of cucurbits (zucchini (Cucurbita pepo), melon (C. melo), cucumber (Cucumis sativus) and watermelon (Citrullus lanatus)) and in their progenies. As the assayed seedlings remained symptomless, we increased the reliability and accuracy of detection in these samples by searching for replicative forms of ToLCNDV by combining Southern blot hybridization and rolling-circle amplification (RCA). However, integral genomic DNA was not identified in the plants of offspring. Although the seedborne nature of ToLCNDV was confirmed, our results do not support the transmission of this virus from contaminated seeds to progeny.

New diamond coatings for a safer electrolytic disinfection.

In this work, a new coating of boron-doped diamond ultra-nanocrystalline (U-NBDD), tailored to prevent massive formation of perchlorates during disinfection, is evaluated as electrode for the reclaiming of treated secondary wastewater by the electrochemically assisted disinfection process. Results obtained are compared to those obtained by using a standard electrode (STD) that was evaluated as a standard in previous research showing outstanding performance for this application. First tests were carried out to evaluate the chlorine speciation obtained after the electrolysis of synthetic chloride solutions at two different ranges of current densities. Concentrations of hypochlorite obtained using the U-NBDD anode at 25 mA cm-2 were 1.5-fold higher, outperforming STD anode; however, at 300 mA cm-2, an overturn on the behavior of anodes occurs where the amount of hypochlorite produced on STD anode was 1.5-fold higher. Importantly, at low current density the formation of chlorates and perchlorates is null using U-NBDD. Then, the disinfection of the real effluent of the secondary clarifier of a municipal wastewater treatment facility is assessed, where inactivation of Escherichia coli is achieved at low charge applied per volume electrolyzed (0.08 A h L-1) at 25 mA cm-2 using the U-NBDD. These findings demonstrate the appropriateness of the strategy followed in this work to obtain safer electro-disinfection technologies for the reclaiming of treated wastewater.

Sustainable integrated process for cogeneration of oxidants for VOCs removal.

This study upgrades the sustainability of environmental electrochemical technologies with a novel approach consisting of the in-situ cogeneration and use of two important oxidants, hydrogen peroxide (H2O2) and Caro's acid (H2SO5), manufactured with the same innovative cell. This reactor was equipped with a gas diffusion electrode (GDE) to generate cathodically H2O2, from oxygen reduction reaction, a boron doped diamond (BDD) electrode to obtain H2SO5, via anodic oxidation of dilute sulfuric acid, and a proton exchange membrane to separate the anodic and the cathodic compartment, preventing the scavenging effect of the interaction of oxidants. A special design of the inlet helps this cell to reach simultaneous efficiencies as high as 99% for H2O2 formation and 19.7% for Caro's acid formation, which means that the cogeneration reaches efficiencies over 100% in the uses of electric current to produce oxidants. The two oxidants' streams produced were used with different configurations for the degradation of three volatile organic compounds (benzene, toluene, and xylene) in a batch reactor equipped with a UVC-lamp. Among different alternatives studied, the combination H2SO5/H2O2 under UVC irradiation showed the best results in terms of degradation efficiency, demonstrating important synergisms as compared to the bare technologies.

Cork barriers for the remediation of soils polluted with lindane.

The in-situ removal of lindane from spiked soil was studied using cork barriers combined with electrokinetic and ohmic heating soil remediation processes. Both vertical and horizontal cork barriers have been evaluated to retain pollutants mobilized by electro-osmotic flow or volatilized by ohmic heating. Moreover, the addition of surfactant solutions in electrolyte wells has been evaluated to promote the dragging of lindane by electrokinetic fluxes. Results indicated that the drag of lindane by liquid flows is not as important as expected, opposite to what happened with the dragging by gaseous flows. The retention of gaseous lindane was also confirmed in adsorption tests carried out in a column packed with cork granules. The addition of surfactant had a very limited effect on the mobility of lindane, and dragging of this species to the electrode wells or to a permeable reactive barrier. On the contrary, the reactivity of lindane during the electrochemical treatments is relevant due to the electrokinetic basic front promoting the in-situ conversion of lindane into less chlorinated pollutants.

Cleaning technologies integrated in duct flows for the inactivation of pathogenic microorganisms in indoor environments: A critical review of recent innovations and future challenges.

Pathogenic microorganisms are a major concern in indoor environments, particularly in sensitive facilities such as hospitals, due to their potential to cause nosocomial infections. This study evaluates the concentration of airborne bacteria and fungi in the University Hospital Complex of Albacete (Spain), comparing the results with recent literature. Staphylococcus is identified as the most prevalent bacterial genus with a percentage distribution of 35%, while Aspergillus represents the dominant fungal genus at 34%. The lack of high Technology Readiness Levels (TRL 6, TRL 7) for effective indoor air purification requires research efforts to bridge this knowledge gap. A screening of disinfection technologies for pathogenic airborne microorganisms such as bacteria and fungi is conducted. The integration of filtration, irradiation or and (electro)chemical gas treatment systems in duct flows is discussed to enhance the design of the air-conditioning systems for indoor air purification. Concerns over microbial growth have led to recent studies on coating commercial fibrous air filters with antimicrobial particles (silver nanoparticles, iron oxide nanowires) and polymeric materials (polyaniline, polyvinylidene fluoride). Promising alternatives to traditional short-wave UV-C energy for disinfection include LED and Far-UVC irradiation systems. Additionally, research explores the use of TiO2 and TiO2 doped with metals (Ag, Cu, Pt) in filters with photocatalytic properties, enabling the utilization of visible or solar light. Hybrid photocatalysis, combining TiO2 with polymers, carbon nanomaterials, or MXene nanomaterials, enhances the photocatalytic process. Chemical treatment systems such as aerosolization of biocidal agents (benzalkonium chloride, hydrogen peroxide, chlorine dioxide or ozone) with their possible combination with other technologies such as adsorption, filtration or photocatalysis, are also tested for gas disinfection. However, the limited number of studies on the use of electrochemical technology poses a challenge for further investigation into gas-phase oxidant generation, without the formation of harmful by-products, to raise its TRL for effectively inactivating airborne microorganisms in indoor environments.

Advanced oxidation and a metrological strategy based on CLC-MS for the removal of pharmaceuticals from pore & surface water.

In this work, it is studied the photolysis, electrolysis, and photo-electrolysis of a mixture of pharmaceutics (sulfadiazine, naproxen, diclofenac, ketoprofen and ibuprofen) contained in two very different types of real water matrices (obtained from surface and porewater reservoirs), trying to clarify the role of the matrix on the degradation of the pollutants. To do this, a new metrological approach was also developed for screening of pharmaceuticals in waters by capillary liquid chromatography mass spectrometry (CLC-MS). This allows the detection at concentrations lower than 10 ng mL-1. Results obtained in the degradation tests demonstrate that inorganic composition of the water matrix directly influences on the efficiency of the drugs removal by the different EAOPs and better degradation results were obtained for experiments carried out with surface water. The most recalcitrant drug studied was ibuprofen for all processes evaluated, while diclofenac and ketoprofen were found to be the easiest drugs for being degraded. Photo-electrolysis was found to be more efficient than photolysis and electrolysis, and the increase in the current density was found to attain a slight improvement in the removal although with an associated huge increase in the energy consumption. The main reaction pathways for each drug and technology were also proposed.

Combining Soil Vapor Extraction and Electrokinetics for the Removal of Hexachlorocyclohexanes from Soil.

This paper focuses on the evaluation of the mobility of four hexachlorocyclohexane (HCH) isomers by soil vapor extraction (SVE) coupled with direct electrokinetic (EK) treatment without adding flushing fluids. SVE was found to be very efficient and remove nearly 70 % of the four HCH in the 15-days of the tests. The application of electrokinetics produced the transport of HCH to the cathode by different electrochemical processes, which were satisfactorily modelled with a 1-D transport equation. The increase in the electric field led to an increase in the transport of pollutants, although 15 days was found to be a very short time for an efficient transportation of the pollutants to the nearness of the cathode. Loss of water content in the vicinity of the cathode warns about the necessity of using electrokinetic flushing technologies instead of simple direct electrokinetics. Thus, results point out that direct electrokinetic treatment without adding flushing fluids produced low current intensities and ohmic heating that contributes negatively to the performance of the SVE process. No relevant differences were found among the removal of the four isomers, neither in SVE nor in EK processes.

Understanding the influence of the bioaerosol source on the distribution of airborne bacteria in hospital indoor air.

The composition and concentration of airborne microorganisms in hospital indoor air has been reported to contain airborne bacteria and fungi concentrations ranged 101-103 CFU/m3 in inpatients facilities which mostly exceed recommendations from the World Health Organization (WHO). In this work, a deeper knowledge of the performance of airborne microorganisms would allow improving the designs of the air-conditioning installations to restrict hospital-acquired infections (HAIs). A solution containing Escherichia coli (E. coli) as a model of airborne bacteria was nebulized using the Collison nebulizer to simulate bioaerosols in various hospital areas such as patients' rooms or bathrooms. Results showed that the bioaerosol source had a significant influence on the airborne bacteria concentrations since 4.00 102, 6.84 103 and 1.39 104 CFU mL-1 were monitored during the aerosolization for 10 min of urine, saliva and urban wastewater, respectively. These results may be explained considering the quite narrow distribution profile of drop sizes around 1.10-1.29 µm obtained for urban wastewater, with much vaster distribution profiles during the aerosolization of urine or saliva. The airborne bacteria concentration may increase up to 107 CFU mL-1 for longer sampling times and higher aerosolization pressures, causing several cell damages. The cell membrane damage index (ID) can vary from 0 to 1, depending on the genomic DNA releases from bacteria. In fact, the ID of E. coli was more than two times higher (0.33 vs. 0.72) when increasing the pressure of air flow was applied from 1 to 2 bar. Finally, the ventilation air flow also affected the distribution of bioaerosols due to its direct relationship with the relative humidity of indoor air. Specifically, the airborne bacteria concentration diminished almost below 3-logs by applying more than 10 L min-1 during the aerosolization of urine due to their inactivation by an increase in their osmotic pressure.

Enhancement of the Green H2 Production by Using TiO2 Composite Polybenzimidazole Membranes.

This study reports the hydrogen production using TiO2 based composite polybenzimidazole membranes through the SO2 depolarized electrolysis that requires lower energy input than the direct water electrolysis. Composite membranes prepared and studied in this work showed very promising results in terms of proton conductivity, chemical stability, and crossover. Thus, a reduction in SO2 crossover was observed with the increase of the concentration of TiO2, obtaining reductions as high as 42% with the 3.0 wt% TiO2-PBI membrane at 120 °C. Higher hydrogen production rates and Faradaic efficiencies were achieved by all the composite membranes, with an optimum for the 1.0 wt% TiO2-PBI membrane (with this membrane, the production of hydrogen increased a 53% at 110 °C and a 49% at 120 °C as compared with the standard PBI membrane), demonstrated the benefit of the use of composite membranes with respect to the standard one for green hydrogen production.

Therapeutic recreation camps for youth with childhood-onset systemic lupus erythematosus: perceived psychosocial benefits.

BACKGROUND: The psychosocial burden of having a chronic disease can be substantial for adolescents with childhood-onset systemic lupus erythematosus (cSLE). Current literature is scarce on interventions that can improve psychosocial outcomes for this population. Therapeutic recreation camps have been proposed as a beneficial experience for chronically ill pediatric populations. However, their effective components have not been well characterized in patients with cSLE. In this study, we sought to understand the various components of the camp experience for adolescents with cSLE from both the patient and parent perspective. METHODS: We recruited patients with cSLE who had participated in one or more annual, weekend-long recreational lupus camp(s) near Dallas, Texas. Semi-structured in-depth telephone interviews were conducted from March-June 2020 with both the patients and parents. Questions focused on overall patient experience, psychosocial impact of camp participation, coping skills gained, and opportunities to prepare for the transition from pediatric to adult care. Interviews were coded and analyzed using inductive thematic analysis. RESULTS: We interviewed 9 current and former campers (ages 16-24), including a current camp counselor, and 3 of their parents separately. Reported benefits included a positive impact on social support through peer bonding, opportunities to develop coping mechanisms through structured activities and peer/medical staff interactions, opportunities for education about the cSLE disease experience, improved adherence through peer modeling, overall increase in self-efficacy, and better parental insight into the patient experience. Participants also provided suggestions for expansion and improvement in program development to optimize educational opportunities for both campers and parents. In addition, they advocated for longitudinal social support and community building. CONCLUSIONS: In this qualitative study, in which cSLE patients and their parents reflected on their experiences with therapeutic recreation camps, we found several perceived benefits impacting the patient and parent experience. Participants expressed a desire for more educational opportunities that could contribute to their successful transition from pediatric to adult care. Further studies are needed to demonstrate the effects of therapeutic recreation camps on the psychosocial health of this population.

Electrochemical Production of Hydrogen Peroxide in Perchloric Acid Supporting Electrolytes for the Synthesis of Chlorine Dioxide.

This work focuses on the electrochemical production of hydrogen peroxide in supporting electrolytes containing perchlorate ions for being used as a reagent in the reduction of chlorates to produce chlorine dioxide, as a first step in the manufacture of portable ClO2 production devices. This study evaluates the effect of the current density, pressure, and temperature on the production of hydrogen peroxide, and concentrations over 400 mg L-1 are reached. The average rate for the formation of hydrogen peroxide is 9.85 mg h-1, and the effect of increasing electrolyte concentration (3.0 and 30.0 g L-1 perchloric acid), intensity, and pressure results in values of, respectively, -2.99, -4.49, and +7.73 mg h-1. During the manufacturing process, hydrogen peroxide is decomposed through two mechanisms. The average destruction rate is 1.93 mg h-1, and the effects of the three factors results in values of, respectively, +0.07, +0.11, and -0.12 mg h-1. Solutions of this hydrogen peroxide produced electrochemically in a perchloric acid aqueous electrolyte were used to reduce chlorates in strongly acidic media and produce chlorine dioxide. Conversions of around 100% were obtained, demonstrating that this electrochemical product can be used efficiently to reduce chlorates to chlorine dioxide.

Carotenoid fortification of zucchini fruits using a viral RNA vector.

BACKGROUND: Carotenoids are health-promoting metabolites in livestock and human diets. Some important crops have been genetically modified to increase their content. Although the usefulness of transgenic plants to alleviate nutritional deficiencies is obvious, their social acceptance has been controversial. RESULTS: Here, we demonstrate an alternative biotechnological strategy for carotenoid fortification of edible fruits in which no transgenic DNA is involved. A viral RNA vector derived from zucchini yellow mosaic virus (ZYMV) was modified to express a bacterial phytoene synthase (crtB), and inoculated to zucchini (Cucurbita pepo L.) leaves nurturing pollinated flowers. After the viral vector moved to the developing fruit and expressed crtB, the rind and flesh of the fruits developed yellow-orange rather than green color. Metabolite analyses showed a substantial enrichment in health-promoting carotenoids, such as α- and ß-carotene (provitamin A), lutein and phytoene, in both rind and flesh. CONCLUSION: Although this strategy is perhaps not free from controversy due to the use of genetically modified viral RNA, our work does demonstrate the possibility of metabolically fortifying edible fruits using an approach in which no transgenes are involved.

Enhancing soil vapor extraction with EKSF for the removal of HCHs.

This paper evaluates the combination of electrokinetic soil flushing (EKSF) with soil vapor extraction (SVE) for the removal of four hexachlorocyclohexane (HCH) isomers contained in a real matrix. Results demonstrate that the combination of EKSF and SVE can be positive, but it is required the application of high electric fields (3 V cm-1) in order to promote a higher temperature in the system, which improves the volatilization of the HCH contained in the system. Electrokinetic transport is also enhanced with the application of higher electric gradients, but these transport processes are slower than the volatilization processes, which are the primary in this system. Hence collection of species in the electrolyte wells is negligible as compared to the compound dragged with air by the SVE but the temperature increase demonstrates a good performance. Combination of EKSF with SVE can efficiently exhaust the four HCH isomers reaching a removal of more than 90% after 15 days of treatment (20% more than values attained by SVE) but it is required the application of high electric fields to promote a higher temperature in the system (to improve the volatilization) and EK transport (to improve the dragging). 1-D transport model can be easily used to estimate the average pore water velocity and the effective diffusion of each compound under the different experimental conditions tested.

Disinfection of polymicrobial urines by electrochemical oxidation: Removal of antibiotic-resistant bacteria and genes.

In this work, data obtained from the University Hospital Complex of Albacete (Spain) were selected as a case study to carry out the disinfection experiments. To do this, different configurations of electrochemical reactors were tested for the disinfection of complex urines. Results showed that 4-6 logs bacterial removal were achieved for every bacterium tested when working with a microfluidic flow-through reactor after 180 min (0.423 Ah dm-3). The MIKROZON® cell reached a total disinfection after 60 min (1.212 Ah dm-3), causing severe damages induced in the cell walls observed in SEM images. The concentration profiles of the electrogenerated disinfectants in solution could explain the differences observed. Additionally, a mean decrease in the ARGs concentration ranked as follows: blaKPC (4.18-logs) > blaTEM (3.96-logs) > ermB (3.23-logs) using the MIKROZON® cell. This electro-ozonizer could be considered as a suitable alternative to reduce the risk of antibiotic resistance spread. Hence, this study provides an insight into different electrochemical reactors for the disinfection of complex hospital urine matrices and contributes to reduce the spread of antibiotic resistance through the elimination of ARGs. A topic of great importance nowadays that needs to be further studied.

Electrochemical Technologies to Decrease the Chemical Risk of Hospital Wastewater and Urine.

The inefficiency of conventional biological processes to remove pharmaceutical compounds (PhCs) in wastewater is leading to their accumulation in aquatic environments. These compounds are characterized by high toxicity, high antibiotic activity and low biodegradability, and their presence is causing serious environmental risks. Because much of the PhCs consumed by humans are excreted in the urine, hospital effluents have been considered one of the main routes of entry of PhCs into the environment. In this work, a critical review of the technologies employed for the removal of PhCs in hospital wastewater was carried out. This review provides an overview of the current state of the developed technologies for decreasing the chemical risks associated with the presence of PhCs in hospital wastewater or urine in the last years, including conventional treatments (filtration, adsorption, or biological processes), advanced oxidation processes (AOPs) and electrochemical advanced oxidation processes (EAOPs).

A review on disinfection technologies for controlling the antibiotic resistance spread.

The occurrence of antibiotic-resistant bacteria (ARB) in water bodies poses a sanitary and environmental risk. These ARB and other mobile genetic elements can be easily spread from hospital facilities, the point in which, for sure, they are more concentrated. For this reason, novel clean and efficient technologies are being developed for allowing to remove these ARB and other mobile genetic elements before their uncontrolled spread. In this paper, a review on the recent knowledge about the state of the art of the main disinfection technologies to control the antibiotic resistance spread from natural water, wastewater, and hospital wastewater (including urine matrices) is reported. These technologies involve not only conventional processes, but also the recent advances on advanced oxidation processes (AOPs), including electrochemical advanced oxidation processes (EAOPs). This review summarizes the state of the art on the applicability of these technologies and also focuses on the description of the disinfection mechanisms by each technology, highlighting the promising impact of EAOPs on the remediation of this important environmental and health problem.

Photoelectrocatalytic treatment of levofloxacin using Ti/MMO/ZnO electrode.

Here, the antibiotic levofloxacin (LFX) widely used and detected in the environment was degraded by photoelectrolysis using a new electrode based on zinc oxide (ZnO) and a mixture of mixed oxides of ruthenium and titanium (MMO). The influence of the potential and irradiation of UV light was investigated in the photostability of the Ti/MMO/ZnO electrode and in the degradation of the antibiotic. The experiments were conducted at different pH values (5.0, 7.0 and 9.0) in sodium sulfate solution in a glass reactor with central lighting. It was observed that the new Ti/MMO/ZnO electrode has good stability under light irradiation and potential, presenting excellent photocurrent and high photoactivity in LFX photoelectrolysis. The removal efficiency of the compound was directly related to the formation of oxidizing species in solution, the photo-generated charges on the electrode and the electrostatic characteristics of the molecule. The mineralization rate, the formation of reaction intermediates and short chain carboxylic acids (acetic, maleic, oxalic and oxamic acid), in addition to the formation of N-mineral species (NO3- and NH4+) was dependent on the pH of the solution and the investigated processes: photoelectrolysis was more efficient than photolysis, which, in turn, was more efficient than electrolysis. The synergistic effect and the high rate of degradation of LFX after 4.0 h of treatment (100%) observed in photoelectrolysis at alkaline pH, was associated with the high stability of the Ti/MMO/ZnO electrode at this pH, the photoactivation of sulfate ions and the ease generation of oxidizing radicals, such as OH.